Before You Get Started
Premier Remotes Boatlift Controls Installation Instructions
Read All Directions before Installation. Installation should be performed by a qualified electrician adhering to the National Electric Code. These instructions do not supersede the National Electric Code or any local codes. It is the recommendation of Premier Remotes to wire all boat lift controls at 240 volts with neutral and ground. Additionally, GFCI must be provided. The lamp feature will not operate if the controller is wired at 240 volts without neutral. The controller can be wired at 120 volts with neutral but motor loads must be considered.
Tools Required
- 5/16 (4mm) standard slotted screwdriver
- 1/8 standard slotted screwdriver
- Wire strippers
- Drill or Impact driver with bits
General Specification
- Designed to operate at 120/240VAC
- Box will operate 1 motor, 2 motor, and 4 motor lifts
- The lamp supply feeds need the neutral leg of the 240VAC connected in order to operate lamp feature.
- Please see Chart 1 for suggested wire size between the main overload protection and the motors.
- Each lamp control will support up to 800 watts each; you must consider feeder load to properly size the wire to support lighting demand. All lighting demand is supported by L1. If you are using the lighting function, please ensure the circuit is large enough to support the motor loads and the lighting loads. Please See Chart 2.
Caution
Failure to wire the control unit correctly can damage the printed circuit board and void warranty. Please verify the unit and motors are wired correctly before energizing the unit.
Warning
Voltage drop and lighting loads must be considered for the Premier Remote Controller to function properly. Incorrect wiring can result in damage to the Premier Remote Controller and boat lift motors! Please read all the instructions prior to installation. Please refer to the motor label for ampacity usage and code compliance. Please refer to Chart 1 as a reference.
Installation
1. Wiring Procedure
All Premier Remote control units come pre-wired for 240V applications. To convert the premier remote controller to 120V, install the provided jumper wire in the 120V jumper terminal that is...
1. Wiring Procedure
All Premier Remote control units come pre-wired for 240V applications. To convert the premier remote controller to 120V, install the provided jumper wire in the 120V jumper terminal that is...
2. Wiring the motors
The premier remote circuit board is marked with motor connectors 1, 2, 3, and 4. The markings on the PCB indicate standard boat lift wiring colors from left to right....
2. Wiring the motors
The premier remote circuit board is marked with motor connectors 1, 2, 3, and 4. The markings on the PCB indicate standard boat lift wiring colors from left to right....
3. Front panel installation
Caution - Do not insert the end of the ribbon into the PCB board while energized. This can cause a short resulting in the motors engaging and running either up...
3. Front panel installation
Caution - Do not insert the end of the ribbon into the PCB board while energized. This can cause a short resulting in the motors engaging and running either up...
4. Panel Operation
UP/DOWN Button Press and hold the UP or DOWN button to move the lift in the desired direction. Release the Up or Down button to stop the lift. The lift...
4. Panel Operation
UP/DOWN Button Press and hold the UP or DOWN button to move the lift in the desired direction. Release the Up or Down button to stop the lift. The lift...
5. Limit switch
Travel limit switches must be properly installed and adjusted. Regardless of manual or automatic mode of operation, the activation of the limit switch in the given direction will stop the...
5. Limit switch
Travel limit switches must be properly installed and adjusted. Regardless of manual or automatic mode of operation, the activation of the limit switch in the given direction will stop the...
6. Changing motor direction
Changing motor direction can be done by changing the direction of the motors at the motor wiring or at the Premier Remote Controller. To change the motor direction, on “T”...
6. Changing motor direction
Changing motor direction can be done by changing the direction of the motors at the motor wiring or at the Premier Remote Controller. To change the motor direction, on “T”...
7. Troubleshooting
Control Box has No Power - Check and Verify power at terminal block using a multimeter. Remove two fuses and check and verify ampacity. All Motors go in the wrong...
7. Troubleshooting
Control Box has No Power - Check and Verify power at terminal block using a multimeter. Remove two fuses and check and verify ampacity. All Motors go in the wrong...
Download The App
Already a proud owner of a Premier Remotes lift controller or have friends and family who are? Take control of any of our smart lifts by simply downloading the app and entering the provided security pin code. Seamlessly connect to the power of remote boat lift control and unlock a world of convenience and freedom.
